Ok, that's not what you want, but it could work on Excel.
If someone here can add "excel.application", and any information to make it...
JEFMAN
PC-DMIS Ultra Guru
Last Activity: Today, 07:43 AM
Joined: 04-15-2008
Location: France
-
Something like this ?
...Code:DO/ V1=FILE/DIALOG,Choose a file to delete. V2=FILE/EXISTS,V1 IF/V2<>0 COMMENT/OPER,File exists.
Leave a comment:
-
2022.2 sp5
https://downloads.ms.hexagonmi.com/P...2022.2/SP5/x64
Funny, here, it appears at 03.31.2023
https:/... -
I would try to measure it directly on the granite, but with a probe angle important (like A80, for example, to limit the force.
You could also decrease...Leave a comment:
-
I would measure the gage block along X with A0B0, and along Y with A0B90 (along Y with A0B0 is already done).
If the defect turns with the probe,...Leave a comment:
-
I use 2022.1, seems to be ok (some crashes sometimes, but not too often), we also have 2023.1 on another cmm, seems to be ok.Leave a comment:
-
How much ?Leave a comment:
-
2021.2 sp11
https://downloads.ms.hexagonmi.com/P...021.2/SP11/x64
Release Notes - 2021.2 SP11
*************************************************... -
T1A0B0 seems to be bad also.
You should reset to theo, and re-locate the sphere with the master probe....Leave a comment:
-
I would try the block test with A0B90.
I would also clean the ball stylus (once, the ball was unglued, but it was not visible- it fall down during...Leave a comment:
-
Origin XY on CIR1, rotate X CIR1 to CIR2
ASSIGN/ANGLE1=ATAN((CIR1.R-CIR2.R)/CIR2.X
ASSIGN/PT_1=CIR2.R*MPOINT(-SIN(ANGLE),COS(ANGLE),0)...Leave a comment:
-
Can you give us what you measured ? (circles, lines, ...)
What Dismas121 said should work, if you replace "ANGLE" by your angle dimension...Leave a comment:
-
So you could try :
1,1=1
1,2=2
1,3=3
2,1=4
2,2=5...
So try to recall AVERAGE[1], AVERAGE[2].....Leave a comment:
-
I would say, if you want to use "COUNT", that COUNT=0 should be in loop V11.
If you write it in loop V20, then, it's zero at each begining...Leave a comment:
-
For memory, the length of a cross product is also the surface of the parallelogram constructed from both vectors (so the surface of the triangle is half...Leave a comment:
-
real cross product function
Here a little code to avoid the problem of applying "UNIT" to "CROSS" in the tool box (the cross product of the tool box gives a vector... -
CMM = Characterization Magic Manipulation ?????
Even if I think it's a very bad idea to accept OOT parts without a real customer acceptance, you...Leave a comment:
-
You can also calibrate offsets by using this prog (with a mate sphere like this of the CMS106)
a little program to improve cmmv offsets calibration...Leave a comment:
-
NinjaBadger : He's using a CMMV, so it's not a vision machine...
Waslam828 : First, calibrate the master probe (tactile) on the sphere, then...Leave a comment:
-
2022.1 sp9
Metrology Software Distribution - /PC-DMIS-Versions/Release/2022.1/SP9/x64> (hexagonmi.com)
Release Notes - 2022.1 SP9
...
No activity results to display
Leave a comment: