Program from Renishaw

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Program from Renishaw

    Please take a look this the program below,renishaw sent it to me yesterday.I
    ran it,but I did not get the results the file was emthy,renishaw said that maybe the path for the file save was write protected.Please advice.


    , MCGFILE =FILE/OPEN,C:\DEFAULT.DMO,WRITE
    COMMENT/REPT,TYPE_CODE=STD
    COMMENT/DOC,NO,DECPL/DIST,4,VEC,4
    MOVESPEED/ 0.656
    TOUCHSPEED/ 0.052
    MODE/MANUAL
    0 =ALIGNMENT/START,RECALL:, LIST= YES
    ALIGNMENT/END
    COMMENT/READOUT,NO,Measure the MCG pivot sphere
    MOVE/POINT,NORMAL,-288.5,-288.5,0
    MOVE/POINT,NORMAL,-156.135,-376.943,0
    MOVE/POINT,NORMAL,0,-408,0
    THEO/0,268.701,268.701,0,0.7071068,0.7071068
    ACTL/0,268.701,268.701,0,0.7071068,0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,0,268.701,268.701,0,0.7071068,0.70710 68,0,268.701,268.701,USE THEO = YES
    MOVE/POINT,NORMAL,288.5,0,-288.5
    MOVE/POINT,NORMAL,204,204,-288.5
    PT52 =FEAT/POINT,RECT
    THEO/190,190,-268.701,0.5000024,0.5000024,-0.7071034
    ACTL/190,190,-268.701,0.5000024,0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,190,190,-268.701,0.5000024,0.5000024,-0.7071034,190,190,-268.701,USE THEO = YES
    ENDMEAS/
    PT53 =FEAT/POINT,RECT
    THEO/190,190,-268.701,0.5000024,0.5000024,-0.7071034
    ACTL/190,190,-268.701,0.5000024,0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,190,190,-268.701,0.5000024,0.5000024,-0.7071034,190,190,-268.701,USE THEO = YES
    ENDMEAS/
    PT54 =FEAT/POINT,RECT
    THEO/190,190,-268.701,0.5000024,0.5000024,-0.7071034
    ACTL/190,190,-268.701,0.5000024,0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,190,190,-268.701,0.5000024,0.5000024,-0.7071034,190,190,-268.701,USE THEO = YES
    ENDMEAS/
    MOVE/POINT,NORMAL,204,204,-288.5
    MOVE/POINT,NORMAL,0,288.5,-288.5
    PT55 =FEAT/POINT,RECT
    THEO/0,268.701,-268.701,0,0.7071068,-0.7071068
    ACTL/0,268.701,-268.701,0,0.7071068,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,0,268.701,-268.701,0,0.7071068,-0.7071068,0,268.701,-268.701,USE THEO = YES
    ENDMEAS/
    PT56 =FEAT/POINT,RECT
    THEO/0,268.701,-268.701,0,0.7071068,-0.7071068
    ACTL/0,268.701,-268.701,0,0.7071068,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,0,268.701,-268.701,0,0.7071068,-0.7071068,0,268.701,-268.701,USE THEO = YES
    ENDMEAS/
    PT57 =FEAT/POINT,RECT
    THEO/0,268.701,-268.701,0,0.7071068,-0.7071068
    ACTL/0,268.701,-268.701,0,0.7071068,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,0,268.701,-268.701,0,0.7071068,-0.7071068,0,268.701,-268.701,USE THEO = YES
    ENDMEAS/
    MOVE/POINT,NORMAL,0,288.5,-288.5
    MOVE/POINT,NORMAL,-204,204,-288.5
    PT58 =FEAT/POINT,RECT
    THEO/-190,190,-268.701,-0.5000024,0.5000024,-0.7071034
    ACTL/-190,190,-268.701,-0.5000024,0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-190,190,-268.701,-0.5000024,0.5000024,-0.7071034,-190,190,-268.701,USE THEO = YES
    ENDMEAS/
    PT59 =FEAT/POINT,RECT
    THEO/-190,190,-268.701,-0.5000024,0.5000024,-0.7071034
    ACTL/-190,190,-268.701,-0.5000024,0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-190,190,-268.701,-0.5000024,0.5000024,-0.7071034,-190,190,-268.701,USE THEO = YES
    ENDMEAS/
    PT60 =FEAT/POINT,RECT
    THEO/-190,190,-268.701,-0.5000024,0.5000024,-0.7071034
    ACTL/-190,190,-268.701,-0.5000024,0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-190,190,-268.701,-0.5000024,0.5000024,-0.7071034,-190,190,-268.701,USE THEO = YES
    ENDMEAS/
    MOVE/POINT,NORMAL,-204,204,-288.5
    MOVE/POINT,NORMAL,-288.5,0,-288.5
    PT61 =FEAT/POINT,RECT
    THEO/-268.701,0,-268.701,-0.7071068,0,-0.7071068
    ACTL/-268.701,0,-268.701,-0.7071068,0,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-268.701,0,-268.701,-0.7071068,0,-0.7071068,-268.701,0,-268.701,USE THEO = YES
    ENDMEAS/
    PT62 =FEAT/POINT,RECT
    THEO/-268.701,0,-268.701,-0.7071068,0,-0.7071068
    ACTL/-268.701,0,-268.701,-0.7071068,0,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-268.701,0,-268.701,-0.7071068,0,-0.7071068,-268.701,0,-268.701,USE THEO = YES
    ENDMEAS/
    PT63 =FEAT/POINT,RECT
    THEO/-268.701,0,-268.701,-0.7071068,0,-0.7071068
    ACTL/-268.701,0,-268.701,-0.7071068,0,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-268.701,0,-268.701,-0.7071068,0,-0.7071068,-268.701,0,-268.701,USE THEO = YES
    ENDMEAS/
    MOVE/POINT,NORMAL,-288.5,0,-288.5
    MOVE/POINT,NORMAL,-204,-204,-288.5
    PT64 =FEAT/POINT,RECT
    THEO/-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034
    ACTL/-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034,-190,-190,-268.701,USE THEO = YES
    ENDMEAS/
    PT65 =FEAT/POINT,RECT
    THEO/-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034
    ACTL/-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034,-190,-190,-268.701,USE THEO = YES
    ENDMEAS/
    PT66 =FEAT/POINT,RECT
    THEO/-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034
    ACTL/-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,-190,-190,-268.701,-0.5000024,-0.5000024,-0.7071034,-190,-190,-268.701,USE THEO = YES
    ENDMEAS/
    MOVE/POINT,NORMAL,-204,-204,-288.5
    MOVE/POINT,NORMAL,0,-288.5,-288.5
    PT67 =FEAT/POINT,RECT
    THEO/0,-268.701,-268.701,0,-0.7071068,-0.7071068
    ACTL/0,-268.701,-268.701,0,-0.7071068,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,0,-268.701,-268.701,0,-0.7071068,-0.7071068,0,-268.701,-268.701,USE THEO = YES
    ENDMEAS/
    PT68 =FEAT/POINT,RECT
    THEO/0,-268.701,-268.701,0,-0.7071068,-0.7071068
    ACTL/0,-268.701,-268.701,0,-0.7071068,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,0,-268.701,-268.701,0,-0.7071068,-0.7071068,0,-268.701,-268.701,USE THEO = YES
    ENDMEAS/
    PT69 =FEAT/POINT,RECT
    THEO/0,-268.701,-268.701,0,-0.7071068,-0.7071068
    ACTL/0,-268.701,-268.701,0,-0.7071068,-0.7071068
    MEAS/POINT,1
    HIT/BASIC,NORMAL,0,-268.701,-268.701,0,-0.7071068,-0.7071068,0,-268.701,-268.701,USE THEO = YES
    ENDMEAS/
    MOVE/POINT,NORMAL,0,-288.5,-288.5
    MOVE/POINT,NORMAL,204,-204,-288.5
    PT70 =FEAT/POINT,RECT
    THEO/190,-190,-268.701,0.5000024,-0.5000024,-0.7071034
    ACTL/190,-190,-268.701,0.5000024,-0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,190,-190,-268.701,0.5000024,-0.5000024,-0.7071034,190,-190,-268.701,USE THEO = YES
    ENDMEAS/
    PT71 =FEAT/POINT,RECT
    THEO/190,-190,-268.701,0.5000024,-0.5000024,-0.7071034
    ACTL/190,-190,-268.701,0.5000024,-0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,190,-190,-268.701,0.5000024,-0.5000024,-0.7071034,190,-190,-268.701,USE THEO = YES
    ENDMEAS/
    PT72 =FEAT/POINT,RECT
    THEO/190,-190,-268.701,0.5000024,-0.5000024,-0.7071034
    ACTL/190,-190,-268.701,0.5000024,-0.5000024,-0.7071034
    MEAS/POINT,1
    HIT/BASIC,NORMAL,190,-190,-268.701,0.5000024,-0.5000024,-0.7071034,190,-190,-268.701,USE THEO = YES
    ENDMEAS/
    MOVE/POINT,NORMAL,204,-204,-288.5
    MOVE/POINT,NORMAL,353.338,-117.779,-166.565
    MODE/MANUAL
    COMMENT/DOC,NO,$$ EXPORT DATA
    FILE/CLOSE,MCGFILE
    COMMENT/READOUT,NO,The results are exported to "C:\DEFAULT.DMO"

  • #2
    MCGFILE =FILE/OPEN,C:\DEFAULT.DMO,WRITE

    is that where your trying to send it? Thats where you are sending it.
    sigpic

    Comment


    • #3
      Yes,Tha'ts where it went the first time,after it finished I changed the file Path to a different place,Renishaw said that maybe the path save file is write protected,so maybe I will ran the program again and send it to a different directory,since I do not know how to unprotect a write file.

      Comment


      • #4
        The first line of code is that a comment seperator? the , at the front
        , MCGFILE =FILE/OPEN,C:\DEFAULT.DMO,WRITE
        sigpic
        if you had soap on a rope it would be tied to yer ankle

        Comment


        • #5
          Good eye Tom, I think that is it. You may not be executing the File Open command
          <internet bumper sticker goes here>

          Comment


          • #6
            MCG HELP FOR FILE WRITE A PROGRAM TO SHARE

            I did some programming for Renishaw concerning this and i have two programs i wrote for different length arms i will share with anybody that wants them. The MCG tools software that comes with from Renishaw has a problem with the PCDMIS___dmis write code. I run the MCG weekly with these programs so i know they work. the data i get from the output can be compiled in the MCG tools program and i usually see only about a micron of difference from my numbers and the numbers from a B&S calibration. I will send it to whoever wants it and the price is FREE. send me your e-mail address and let me know you want it. after you see the program you will be able to modify your existing programs to get the data from the MCG run. Regards, Scott Bean [email protected]

            Comment


            • #7
              Renishaw program

              Hello Scott

              I'm still having problems with the renishaw program,I just send you an email
              Please send me your programs,so I can try one of them,I'm using 380.00 arm lenth.I appreciate that you're willing to share,you just made my day and my whole year.

              [email protected]

              thanks

              Comment


              • #8
                A big thank you to Scott also. He sent me the programs that he has made
                sigpic

                James Mannes

                Comment


                • #9
                  I'm having problems with my MCG program same issue as with C:\DEFAULT.DMO.WRITE Can anyone help me with this please. Scott Bean offered a free prgrm awhile back could I get a copy of that?

                  Comment


                  • #10
                    C:\DEFAULT.DMO,WRITE

                    Can that helps ?

                    https://www.renishaw.fr/media/pdf/en...de84a2b698.pdf
                    https://www.renishaw.fr/media/doc/ge...0244fecc2.xlsm

                    Comment


                    • #11
                      Found this from the other site, HTH

                      PS Happy new year to all!
                      Attached Files
                      Global S Blue 12.15.10 HH-AS-T2.5 / HP-S-X1h |PC-DMIS CAD++|Quindos7 CAD; Leitz Reference Xi 15.9.7

                      Comment


                      • #12
                        I had to use 1 in "Enter the number of times to repeat each Measured Point" and change these lines of code, so the mcg_tools spreadsheet can import the output file correctly:

                        Code change:

                        Code:
                        FILE/WRITELINE,FPTR,STR(MEAS_POINT_DATA_X)+" "+STR(MEAS_POINT_DATA_Y)+" "+STR(MEAS_POINT_DATA_Z)
                        Original code:

                        Code:
                        FILE/WRITELINE,FPTR,"&lt;X&gt;" + STR(MEAS_POINT_DATA_X) + "&lt;/X&gt;"
                        FILE/WRITELINE,FPTR,"&lt;Y&gt;" + STR(MEAS_POINT_DATA_Y) + "&lt;/Y&gt;"
                        FILE/WRITELINE,FPTR,"&lt;Z&gt;" + STR(MEAS_POINT_DATA_Z) + "&lt;/Z&gt;"
                        And BTW, thanks to Rondog (from this and "the other site").
                        Global S Blue 12.15.10 HH-AS-T2.5 / HP-S-X1h |PC-DMIS CAD++|Quindos7 CAD; Leitz Reference Xi 15.9.7

                        Comment


                        • #13
                          Just found this utility from http://selectcalibration.ca/downloads.html that can import the XML file generated from the original MCG - 3.0 - PC-DMIS 3.7.PRG. There are some other interesting goodies to look for here.
                          Last edited by jleond; 01-03-2019, 08:32 PM.
                          Global S Blue 12.15.10 HH-AS-T2.5 / HP-S-X1h |PC-DMIS CAD++|Quindos7 CAD; Leitz Reference Xi 15.9.7

                          Comment

                          Related Topics

                          Collapse

                          Working...
                          X