Temp sensor defect

[fmred79]

Hi All

I have a trouble when I tried to run a programs that were done under 3.7 MR. I 'm actually running under 3.7 MR3. Does anybody Know about this defect?

The error said: "TR_TSENS, Temperatur Sensor Defect, Temp Corr off". This happens when I try to open the program. After this step, I can't open any program, Then I have to restart all the machine and the controller too.


Does anybody know this error??

Thanks in advance..

[Don Ruggieri]

try off-line

Hi All

I have a trouble when I tried to run a programs that were done under 3.7 MR. I 'm actually running under 3.7 MR3. Does anybody Know about this defect?

The error said: "TR_TSENS, Temperatur Sensor Defect, Temp Corr off". This happens when I try to open the program. After this step, I can't open any program, Then I have to restart all the machine and the controller too.


Does anybody know this error??

Thanks in advance..

I am not sure how this relates to differences between MR1 and MR3, but I've seen this trouble when I've had bad sensors. Open the program in PC-DMIS off-line, delete the temp-comp command, then it should work fine on-line. This will hold you until you get the sensors fixed or replaced.

[fmred79]

Don, I didn't make those programs on MR2, could you explain me where it should be that commands? Should be in the edit window? or another place.

I'm new with pcdmis.

[William Johnson]

It will be in the edit window. It should be at the beginning somewhere.

[fmred79]

I didn't find this command, I tried to open the program offline.

Other question. I didn't find this file the name is serv1.stp

The path of this file is C:/program file/thermal ocx/ serv1.stp


Does anyone know where I can get this file?

Thanks.

[Saliha]

DataSave

If you have a floppy disk as name TEMPCOMP or DATASAVE , you may find it there.

I think sensors are not defected , just you are using wrong parameters for TEMPCOMP.

If you have a backup file of constant.asc , you may find the correct numbers of sensors , then you may enter these numbers to thermal parameters of pc-dmis sw. (Line #50,#51,#52,#53)

like :

#50 index - part sensor : Integer PRT_SENS
1 part's sensor nr
#51 index - x axis sens : Integer X_SENS
4 x axis' sensor nr
5 x axis' sensor nr
0
#52 Index - y axis sens : Integer Y_SENS
2 y axis' sensor nr
3 y axis' sensor nr
0
#53 Index - z axis sens : Integer Z_SENS
7 z axis' sensor nr
8 z axis' sensor nr
0
(this is an example , please DO NOT use numbers abowe.Depending to machine type it might be different)
Just write down the sensor numbers and axis name then fill it to pc-dmis parameters.


An example of serv1.stp file:
S001: 1
S002: 10.0 10.0 10.0 0.0 0.0
S003: 0.000 0.000
S004: 0.000 0.000
S005: 99
S006: 1 4
S007: 0 0 0 0 0 0
S008: 1 1
S009: 2 2 3
S010: 2 4 5
S011: 2 8 7
S012: 0 0
S013: 0 0
S014: 0.00 0.00 0.00 0.00 0.00
S015: 600
S016: 0 0.0
S017: 0 0.0
S018: 99.0
S019: 60000
S020: 0.0 0.0
S021: 190
S022: 0
S023: 10 40
S024: 0
S025: 0
S026: 0
S027: 0
S028: 0
S029: 0
S030: 1

just use notepad.

HTH
Saliha

[fmred79]

Sorry
Sahila

I did'nt have this file, Do you know how i can get it?

Thanks for your reponse

[than_357]

Had that with a program given to us, the individual just deleted the temp sensor reference in the edit window and all was well. Since we don't have temp sensors on our CMMs I don't know what that callout was- sorry.

[Saliha]

Sorry
Sahila

I did'nt have this file, Do you know how i can get it?

Thanks for your reponse

You do not have constant.asc file or serv1.stp file or both?

SERV1.STP :Copy from the msg serv1.stp lines and paste it simply to a notepad document then move to proper folder.

SERV1.STP File for Global Image 091208

S001: 1
S002: 10.0 10.0 10.0 0.0 0.0
S003: 0.000 0.000
S004: 0.000 0.000
S005: 99
S006: 1 4
S007: 0 0 0 0 0 0
S008: 1 1
S009: 2 2 3
S010: 2 4 5
S011: 2 8 7
S012: 0 0
S013: 0 0
S014: 0.00 0.00 0.00 0.00 0.00
S015: 600
S016: 0 0.0
S017: 0 0.0
S018: 99.0
S019: 60000
S020: 0.0 0.0
S021: 190
S022: 0
S023: 10 40
S024: 0
S025: 0
S026: 0
S027: 0
S028: 0
S029: 0
S030: 1


SENSOR.ASC File : Check this file too if present or not.
SENSOR.ASC File for Global Image 091208

Machine Temperature Sensor File
Brown & Sharpe / DEA 32 Sensor System
# Sensor 1
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 2 Serial No 1485
1.1223230295E-03
2.3511802718E-04
8.4534316593E-08
# Sensor 3 Serial No 1740
1.1430681078E-03
2.3180603433E-04
9.7419577364E-08
# Sensor 4 Serial No 1499
1.1393412264E-03
2.3231887342E-04
9.6177180721E-08
# Sensor 5 Serial No 1476
1.1338677249E-03
2.3316203738E-04
9.2553347914E-08
# Sensor 6
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 7 Serial No 1403
1.1376227221E-03
2.3255608981E-04
9.5514590863E-08
# Sensor 8 Serial No 9371
1.1223714285E-03
2.3555564586E-04
7.9576046813E-08
# Sensor 9
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 10
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 11
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 12
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 13
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 14
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 15
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 16
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 17
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 18
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 19
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 20
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 21
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 22
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 23
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 24
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 25
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 26
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 27
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 28
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 29
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 30
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 31
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08
# Sensor 32
1.1207253300E-03
2.3540040000E-04
8.3274691800E-08


CONSTANT.ASC : Normally it should be in folder C:\AUTOTUNE

#50 index - part sensor : Integer PRT_SENS
4
#51 index - x axis sens : Integer X_SENS
9
10
0
#52 Index - y axis sens : Integer Y_SENS
1
2
0
#53 Index - z axis sens : Integer Z_SENS
13
14
0


The last thing , you may check the error status of the machine from hyperterminal .

[fmred79]

I couldn't fix the problem I'm thinking that I have to make the program again ....


Thanks for your help any way.