Converting PC-DMIS to Geomeasure

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Cumofo
    replied
    HIT/BASIC,NORMAL,0.07697,0.56517,-0.06859,-0.0844656,-0.6203825,0.7797379,0
    .07702,0.56399,-0.07174,USE THEO = YES.07702,0.56399,-0.07174,USE THEO = YES
    HIT/BASIC,NORMAL,0.28501,0.48354,-0.07608,-0.3128216,-0.5306255,0.7877685,0
    .28574,0.48215,-0.0787,USE THEO = YES.28574,0.48215,-0.0787,USE THEO = YES


    there are only two hits here. A sphere needs at least four.
    but anyway:
    Hit/basic,normal, o.x,o.y,o.z,o.I,o.J,o.K,i,j,k BUT YOU CAN LEAVE OFF THE LAST THREE IJK'S!

    Leave a comment:


  • cmmmike
    replied
    They follow the same as the theoretical.

    Leave a comment:


  • Guest's Avatar
    Guest replied
    I think I understand the Circle definition but what about the XYZ and IJK in the actual hits?

    HIT/BASIC,NORMAL,0.07697,0.56517,-0.06859,-0.0844656,-0.6203825,0.7797379,0
    .07702,0.56399,-0.07174,USE THEO = YES.07702,0.56399,-0.07174,USE THEO = YES

    I need to know where to take my theoretical points and the vectors so that I can coorilate our program with another program.

    Leave a comment:


  • cmmmike
    replied
    X, Y, Z, I, J, K,
    THEO/0.00005, 0.00016, 0.64154, 0, 0, 1,1.82217

    Hope this helps.

    Mike
    Last edited by cmmmike; 03-28-2006, 12:36 PM.

    Leave a comment:


  • T Miller
    replied
    THEO/0.00005,0.00016,0.64154,0,0,1,1.82217
    X^ Y^ Z^ x, y, z, dia

    Leave a comment:


  • Guest's Avatar
    Guest started a topic Converting PC-DMIS to Geomeasure

    Converting PC-DMIS to Geomeasure

    I'm new to PC-DMIS and I'm trying to convert the PC-DMIS file to Geomeasure. The folowing are a few lines from a sphere measurment in PC_DMIS. I need to know what Coordinates are the Theoretical XYZ points and which are the theoretical vectors. Then I can manually enter them into Geomeasure. Can anyone please help?

    SPHR1 =FEAT/SPHERE,RECT,IN
    THEO/0.00005,0.00016,0.64154,0,0,1,1.82217
    ACTL/-0.00025,-0.00034,0.64551,0,0,1,1.83299
    MEAS/SPHERE,34
    MOVE/CLEARPLANE
    HIT/BASIC,NORMAL,0.07697,0.56517,-0.06859,-0.0844656,-0.6203825,0.7797379,0
    .07702,0.56399,-0.07174,USE THEO = YES.07702,0.56399,-0.07174,USE THEO = YES
    HIT/BASIC,NORMAL,0.28501,0.48354,-0.07608,-0.3128216,-0.5306255,0.7877685,0
    .28574,0.48215,-0.0787,USE THEO = YES.28574,0.48215,-0.0787,USE THEO = YES


    -Chad T.

Related Topics

Collapse

  • dwade
    Dilemma with datums
    by dwade
    What I have run into while looking into correlation issues with a customer is datum feature measurement. The parts were programmed with CAD (and using...
    06-04-2014, 03:13 PM
  • emurray
    Please take a look
    by emurray
    I am running a pre-existing program for one of our parts. The problem I am having (this time) is after I am prompted to take my manual measurments,...
    08-14-2007, 01:32 PM
  • Aguayo
    Program from Renishaw
    by Aguayo
    Please take a look this the program below,renishaw sent it to me yesterday.I
    ran it,but I did not get the results the file was emthy,renishaw said...
    05-10-2006, 09:03 AM
  • j.gonzalez
    accuarcy of a circle
    by j.gonzalez
    i got a 4 circles all measured the same tolerences are .9449/.9454 the cmm is kicking it out at .9456 i manually check the part using an air gage it's...
    06-23-2009, 12:42 PM
  • Ken379128
    Nominals changing
    by Ken379128
    Why when I run thru a program do my nominals keep changing. I go in put them to what I want and when it runs it changes it right back????...
    02-03-2007, 11:29 AM
Working...
X